Market & Policy  |   Project & Contract  |   Technology & Product  |   Corporate News  |   Product News  |
  Cell & Module  |   Production & Inspection  |   Component & Power  |   Solar Material  |
  Worldwide  |   Europe  |   North America  |   APAC  |   Others  |
  Cell & Module  |   Production & Inspection  |   Component & Power  |   Solar Material  |
  Cell & Module  |   Production & Inspection  |   Component & Power  |   Solar Material  |   Agent & Dealer  |
  Free Event Listing
  2012 JUN Issue   |   What is Digital Magazine?  |  How to use  |  Archives  |  Subscription  |  iPad / Mobile  
  Tigo Energy

20% More Energy

Cell & Module

Production & Inspection

Component & Power

Solar Material

<JUN, Issue, 2012>
Cover Story :
DEGER equips two solar parks in Bosnia-H...
Table of
Production & Inspection

The Influence of Sputtering Targets on the Manufacturing Costs and Efficiency of CIGS

Austrian company, PLANSEE’s metals contribute to the performance of photovoltaics and solar thermal applications as coating materials. The metals are highly adhesive and resistant against corrosion and oxidation.
The manufacturing cost reduction in terms of USD per watt is one of the most important challenges for CIGS solar module producers. Especially the sputtering process plays a crucial role in efficiency enhancement. In terms of the issue, monolithic rotary sputtering targets made of molybdenum provide maximum material utilization and contribute to a faster sputtering process.

By Dr. Christoph Adelhelm



The sputtering process is the most important technique for material deposition in CIGS manufacturing. With a better target utilization and high-quality target materials, CIGS producers can reduce their manufacturing costs. New material alloys such as sodium doped molybdenum enhance the efficiency of the solar cells.

Manufacturers of sputtering targets like PLANSEE have two approaches to reduce CIGS module manufacturing costs: In order to lower the material consumption by a better target utilization, the company introduced the new monolithic and dogbone rotary target designs. With MoNa (Molybdenum+ Sodium), the company offers a new material alloy that increases conversion efficiencies.


Monolithic and ‘Dogbone’ Rotary Targets Maximize the Material Utilization


Changing the sputtering system from planar to rotary targets increases the target utilization from about 30% to 75%, which saves expensive raw material. Depositing the molybdenum back contact by monolithic molybdenum rotary targetswhich are completely made of molybdenumgives additional benefits: The expensive bonding of the molybdenum material on a stainless steel backing tube is not required. In addition, a higher sputtering power of up to 30 kW/m can be applied. This creates a very high heat load which cannot be accommodated by bonded-type targets: Indium is used as bonding material which melts at only 156°C thus the risk of de-bonding is eliminated with monolithic targets. A higher sputtering power results in a higher deposition rate and improved thin-film properties, e.g., higher electrical conductivity.

In contrast to the high lateral homogeneity of thin films deposited by sputtering, a sputtered target has generally an erosion profile which is not homogeneousa result of different plasma densities. As a consequence, the targets have to be replaced even if there is sufficient material on most of the target area. To overcome this limitation, targets with varying outer diameter (named ‘dogbone’ for rotary targets) or thickness is a solution to extend the target lifetime and increase the target exchange interval.


Sodium Doped Molybdenum for More Efficiency


Two elements have a big impact on the CIGS cell efficiency: iron (Fe) and sodium (Na). Whereas iron degrades the cell performance by introducing defects in the CIGS structure, sodium has the opposite effect. It concentrates defects at grain boundaries, which is a requirement for achieving high efficiencies.

Low iron levels are only achieved by a high purity of the primary materials as well as a high quality manufacturing process. Especially for molybdenum targets the iron content can vary significantly. The traditional way to introduce sodium into the CIGS absorber is by means of a soda-lime-glass substrate. During the manufacturing process ,sodium diffuses from the glass through the molybdenum back contact into the absorber layer, resulting in a sodium concentration in the order of 0.1 at%. However, reproducibility and lateral homogeneity of this process is low, and flexible substrates do not act as sodium source.

Solar cell producers now have an easy alternative at hand. By sputtering a layer of sodium doped molybdenum, the amount of sodium in the absorber layer can precisely be controlled and reproduced. PLANSEE offers MoNa sputtering targets with high purity and a uniform and fine grained microstructure. Tests in cooperation with the Swiss EMPA institute have already proven their benefits in practice. With sodium doped molybdenum layers, the efficiency of CIGS solar cells could be significantly improved.


Dr. Christoph Adelhelm is Manager of the ‘Application Group Solar’ at PLANSEE SE (www.plansee.com). In his former position, he did thin-film material research at the Max Plack Institute for Plasma Physics.



For more information, please send your e-mails to pved@infothe.com.

2011 www.interpv.net All rights reserved.


     Rapid Metallization Paste Firing of Crystalline Silicon Solar Cells

     Assessing the Viability of Thin PV Glass for Solar Modules

Home l New Product Showcase l Gold Suppliers l Trade Shows l email Newsletter l About InterPV l Help l Site Map l Partnerships l Privacy Policy
Publisher: Choi Jung-sik | Edited by: Lee Sang-yul | Youth Protection Officer: Lee Sang-yul
Copyright Notice ⓒ 2004-2007 www.interpv.net Corporation and its licensors. All rights reserved.